what size nails would you use to install tongue and groove planks

How to Nail Down a Tongue and Groove Wooden Floor Without a .

Setting Nail Heads. You& 39;ll need a nail set when hand-nailing flooring and you should use it when the head is about 1/2 inch out. If you try to nail any deeper than that without a nail set you& 39;ll .【Get Price】

How to Install a Tongue-and-Groove Plank Ceiling how-tos DIY

Start with your first piece: groove facing the wall tongue facing out. Use the framing gun to add a nail to the tongue of the plank and secure in place. For the next piece you will connect the groove of the new piece into the tongue of the first piece.【Get Price】

what nails to use to install cedar tongue and groove « Cedar .

HORIZONTAL or DIAGONAL INSTALLATION: Start at the bottom and work up with the groove edges facing downwards and the tongues up. Cedar T and G up to 6” wide can be “blind nailed” through the tongue at an approximate 45 degree angle with one nail into each framing member.【Get Price】

Tongue and Groove Flooring 101 - Bob Vila

Developed in the late 1800s tongue and groove flooring took off as manufacturers began mass-producing interlocking hardwood planks that eliminated the need for exposed nail heads had been a .【Get Price】

How to Install Tongue and Groove Paneling on Walls and Ceilings

As each section of tongue and groove wall paneling is installed don’t worry about stud/rafters overrun. Secure sections with a nail on the tongue and simply slide in the next cut when you need one. If it doesn’t line up to the stud/rafters the end matching ensures that you won’t have any problems.【Get Price】

How to Build a Tongue and Groove Wall

Then with my nail gun I added 3½ in. trim to both sides of the dining room wall so that the ends of the tongue and groove planks would not be visible. This trim will give the tongue and groove wall a more finished clean look. Step 3. Time for the fun part…adding tongue and groove boards The fun with this kind of millwork is in the name.【Get Price】

What Gauge Nails Do I Need for Tongue and Groove Pine Ceilings .

A nail& 39;s gauge represents its diameter. Common gauges for nails used in tongue and groove installation include 15 16 17 and 18. The gauge of a nail has nothing to do with its length. As such it& 39;s possible to use 15-gauge nails with lengths of 1 inch 1.5 inches or 2 inches.【Get Price】

Tongue and Groove Ceiling Flooring and Walls - Designing Idea

Another way to install tongue and groove flooring is to drive the nails at an angle through the tongue part of the piece of hardwood into the subfloor. This is a physically demanding as well as time consuming process; on top of that it is typically not done well which defeats the purpose of having a tongue and groove system anyways.【Get Price】

How to Install Tongue and Groove Decking DoItYourself.com

Aside from the tongue and groove decking kit you will need to have a few everyday tools and basic knowledge of DIY will help you a lot. Step 1-Preparing the Decking. Assuming you have a simple rectangular area that you are going to apply the decking to simply cut all of the floor planks to the same length. Make sure that these are cut accurately.【Get Price】

How do you blind out tongue and groove nails?

Also asked what kind of nails do you use for tongue and groove? Common gauges for nails used in tongue and groove installation include 15 16 17 and 18. The gauge of a nail has nothing to do with its length. As such it& 39;s possible to use 15-gauge nails with lengths of 1 inch 1.5 inches or 2 inches.【Get Price】

Shiplap Ceiling: How to Install a Tongue and Groove Ceiling DIY

One of the cool things about tongue and groove walls is that you can use a technique called "blind-nailing." If you do it properly you won& 39;t have any nail heads showing or holes to fill. Drive the nails through the shoulder of the tongues into the framing at about a 45-degree angle.【Get Price】

How to Install Tongue and Groove Paneling on Walls or Ceilings .

Install your next row by sliding the grooved side on the tongue of the first row. It can be butted up tight to the previous row. Nail the tongue to the nailing surface. Since the groove side is now secured by the tongue of the first row there is now no need to face nail the board on the groove side. Continue to install rows.【Get Price】

what nails to use to install cedar tongue and groove « Cedar .

For interior as well as exterior use Western Red Cedar tongue and groove T and G paneling can be installed vertically horizontally or diagonally. It is commonly used as an exterior siding and cladding in soffits and for ceilings as well as either interior or exterior accent walls or paneling.【Get Price】

Staple or finish nails to put up tongue and groove wall .

4. Whether or not you have a layer of 1/2-inch drywall or plaster between the studs and the tongue-and-groove boards. The worst case scenario: You live in a cold climate; the walls are insulated with fiberglass batts; and there is no drywall or plaster. That would be bad because that kind of wall leaks air like a sieve. I hate staples because .【Get Price】

How to install a Plank Wall - tongue and groove - Sawdust Girl

How to install a tongue and groove plank wall. Now you are going to nail your planks on the wall. Here are some pointers… Mark your studs. Use a stud finder or knock or drill holes until you find the studs at the top and bottom of the portion of wall you are going to install your planks on.【Get Price】

What Nailer to Use for Tongue and Groove Paneling eHow

For installing tongue-and-groove paneling you need 6d finishing nails. These 2-inch long nails have a narrow head that sinks below the surface of the wood. Nail styles are often not interchangeable between nailers because the guns cannot handle every type of nail -- that is why there are different nailer types.【Get Price】

Install Premium-Quality Faux Wood Tongue and Groove Planks to .

One of the biggest benefits of tongue and groove planks is how easy they are to install. The pieces simply snap together — no gluing or clamping involved. The biggest challenge you’ll face when installing tongue and groove planks is cutting them to size to fit in your space. Tongue and groove planks also form strong joints once they’re .【Get Price】

Basic Finish Nailer Tips Family Handyman

With a trim nailer you can install tongue-and-groove paneling in a fraction of the time. Some carpenters use a finish nailer for this but I like to use my smaller lighter 18-gauge brad nailer especially on ceilings.【Get Price】

How do you install tongue and groove ceiling yourself?

Install Planks Start with your first piece: groove facing the wall tongue facing out. Use the framing gun to add a nail to the tongue of the plank and secure in place. For the next piece you will connect the groove of the new piece into the tongue of the first piece.【Get Price】

How do you blind out tongue and groove nails?

Similarly one may ask what kind of nails do you use for tongue and groove? Common gauges for nails used in tongue and groove installation include 15 16 17 and 18. The gauge of a nail has nothing to do with its length. As such it& 39;s possible to use 15-gauge nails with lengths of 1 inch 1.5 inches or 2 inches.【Get Price】