how to replace a single tongue and groove deck board

Old House Restoration Guide Roofing Roof Sheathing Old .

Old houses with asphalt shingles usually had either tongue-and-groove boards or straight-sided boards abutting. In the 1950s plywood sheathing and particleboard became common and today most standard-construction roofs use either half-inch plywood or particleboard& 39;s big brother oriented-strand board OSB .【Get Price】

How to Repair a Tongue and Groove Deck DoItYourself.com

Use an additional deck post as a way to secure the deck post or simply take the deck post out of the ground and replace it. The deck post will need to be secure before you can move on to replacing the tongue and groove deck boards. Step 3: Replace Tongue and Groove Deck Boards. Purchase replacement tongue and groove deck boards for your deck.【Get Price】

Old House Authority Ask the Authority: Porch Floorboards

When I have to replace floorboards I use the best quality exterior grade tongue and groove lumber I can find. In the Northeast where I live now my local lumberyard stocks vertical grain fir which is dimensionally stable and somewhat rot-resistant.【Get Price】

Replacing Deck Boards DIY - Family Handyman

Angle the saw blade a few degrees so the new board will butt the top edge of the old board tightly. Pull the nails and remove the board Pull the nails that hold the board in the middle. Drive a ’s paw into the wood under the nailhead.【Get Price】

Replacing a few tongue and groove boards.

Sure. But the last board s will need to be face nailed to secure them if the popin fit does not work---since the way to install the last T and G board in the middle is to cut off the bottom of the groove so the board sets against the tongue of the abutting board.【Get Price】

Low-Maintenance Decks DIY Family Handyman

Ripped boards may require reinforcement. Cover the ends with special trim pieces from the manufacturer or a trim board. If using tongue-and-groove boards slope the framing 1/2 in. over 8 ft. to drain any water away from the house and run the decking perpendicular to the house if possible. Fastening【Get Price】

Question: How can I fix my cracked Tongue and Groove ceiling board?

“Tongue and Groove is pretty difficult to repair because you have the tongue and groove from which the board’s interlock with each other.” Todd Host of AskTheContractors.com However it can be repaired but when it’s repaired the tongue is actually going to have to be cut so you can fit the board up there.【Get Price】

How to Remove a Single Piece of Hardwood Flooring. The Art .

The reasons for needing to pull up a single piece of tongue and groove flooring are varied. You might want to see what the floor underneath is like. Your may have peed on it and you want to replace a section without wrecking all the floor around it.【Get Price】

Front Porch Fix-up - This Old House

Prime all the boards& 39; edges and lower faces with fast-drying oil-based primer to protect them from moisture. Squeeze a bead of polyurethane construction adhesive on all the exposed joists then place the groove of a replacement board over the tongue of an old deck board and press the new piece into the adhesive.【Get Price】

How to Repair a Tongue and Groove Deck - Buana Triarta

Take a pry bar to remove the nails and screws that hold the tongue and groove deck boards in place. Remove each of the damaged deck boards that need to be replaced. Check the joists underneath the deck boards for any damage as well. The joists are the boards which the deck boards are attached.【Get Price】

Plank Decking - The Canadian Wood Council - CWC : The .

The 38 mm 1-1/2 in decking has a single tongue and groove while the thicker sizes have a double tongue and groove. Thicknesses greater than 38 mm 1-1/2 in also have 6 mm 1/4 in diameter holes at 760 mm 2.5 ft spacing so that each piece may be nailed to the adjacent one with deck spikes. The standard sizes and profiles are shown below.【Get Price】